Don't get stuck redoing your floor every few years. We'll test your Seattle slab, prep it right and install a Certified Penntek polyurea floor that bonds with your concrete, so you can stop worrying about the garage and start enjoying it.
Cascade Concrete Coatings, a Certified Penntek Dealer based in Woodinville, installs epoxy-style garage floor coatings across Seattle. The floor is Certified Penntek polyurea, not epoxy: a pure polyurea basecoat over 99% solids, a 1,300+ PSI chemical bond with the concrete and a polyaspartic topcoat. A typical garage is finished in one day after a free in-home quote with moisture and hardness testing, and it carries a limited lifetime warranty backed by Penntek.
A lot of them are. Seattle is a city of hills, and on Queen Anne, Magnolia, West Seattle and Capitol Hill the garage often sits under the house, cut into the slope, with board-formed concrete walls on two sides. Water moves through that hillside all winter, and it carries minerals up through the slab. You see it as white rings and chalky blotches that come back no matter how often you sweep.
Flatter parts of the city have their own version. Alley garages behind bungalows in Ballard and Wallingford, mid-century two-car garages in Lake City and Wedgwood, and newer townhome garages full of builder residue. Different ages, same wish. You want a clean floor you never have to redo.
That is where a typical epoxy garage floor lets people down. A quick acid etch, a thin coat, no moisture reading. Epoxy is rigid and is not UV stable, so it cracks when the slab moves and yellows near the door. On a damp hillside slab, trouble often shows up in years 3 to 5. That is the story behind many failed concrete coatings we are asked to replace.
Every Seattle job starts with a moisture and hardness test, then industrial diamond grinding, crack repair with Penntek Mender and a pure polyurea basecoat with a FadeLock UV topcoat. That's how we deliver up to 5x the lifespan of typical epoxy, a 30 to 40 year floor, with a limited lifetime warranty backed by Penntek.
Drag the handle to compare. Every pair is a real floor our team ground, repaired and coated.
The coating is only half of it. Watch the same slab go through what a Seattle garage puts it through, once with typical epoxy or cheap poly and once the way we install Penntek.
Your slab’s age, composition and moisture all matter. We test it first, then choose the Penntek system that fits, adding a moisture barrier when the readings call for it.
Moisture & hardness testedSide-by-side tests on the same slab, in the same conditions. Typical epoxy and cheap poly on one side, certified Penntek on the other.
A floor that fails doesn't just look bad. It means emptying the garage, grinding off the old coating and paying all over again.
For a lot of Seattle families it's the gym, the workshop, the mudroom and the first thing you see when you get home. You've put real money into it. You deserve a floor you never have to think about again, installed by people who treat your home like their own.
Nicole and Sheldon, owners of Cascade Concrete CoatingsHere's what a Certified Penntek floor from our team gives you, long after install day.
Every certified Penntek floor is built in four layers, each doing its own job. Watch it go down layer by layer, then tap a layer to see what it does for your floor.
When moisture readings call for it, we add a two-layer moisture barrier system before the basecoat.
You typed epoxy because that is the word everyone uses. Fair enough. Plenty of homeowners here call our floors epoxy poly garage floors, or just epoxy polyurea, since the steps look similar. The material is different, and on a city slab that difference shows.
The Penntek difference is four things working together:
The basecoat forms a 1,300+ PSI chemical bond with the concrete. The polyaspartic topcoat is non-porous and resists hot tire pickup, oil, salt and chemicals, which matters when wet tires climb a steep driveway in January. FadeLock™ UV stability passed a 16-hour QUV test. See it tested on our side-by-side epoxy and Penntek demo, or read the real difference in a Seattle garage.
Anyone can buy a kit and call themselves a garage floor company. Penntek doesn't sell to just anyone. Our team was vetted, trained hands-on through Penntek Academy and is backed by Penntek's full-time technical support team from prep to finish. That's the Penntek Standard, on every floor we install.

Garages are most of what we do in Seattle, but the same Penntek system protects patios, pool decks, basements and commercial floors.
No pressure and no guesswork. Here is how your project runs from the first visit to the day you park on it. The full installation process has every detail.
Cascade Concrete Coatings is a Certified Penntek Dealer based in Woodinville, a short drive up I-405 and SR 522 from the city. Every job in the city starts the same way, with a free in-home quote where we measure, run a moisture meter and scratch test the concrete for hardness. Then we tell you plainly what your slab needs.
Sometimes the answer is patience. One under-house garage with mineral-stained concrete read 4.7% in June 2025, then 4.5% and 5.5% in July. We came back and tested four times before the floor went down in Mount Everest flake that October. That is the kind of care an old slab deserves.
When a slab needs more protection, we install a two-layer moisture barrier system under the polyurea. When it is ready, a typical garage is done in one day. Either way, you get the reason in writing.
You're probably a great fit if any of these sound familiar.
Garages here tend to be dark. Small windows, deep tuck-under bays and gray winter light all work against you. That is why light flake blends like Mount Everest show up so often here. For porches and entries, color can tie the concrete back to the house, the way Tidal Wave picked up the blue stucco on one storybook home. See every option on our styles and colors page.
Our concrete coating work in the city does not stop at the garage. The portfolio here includes two-car garages, a home gym garage with support posts and a drain, a storybook front porch, a steep entry stair and three building floors. Each one started with the same moisture and hardness tests.
A few more you can tour: a north Seattle garage where years of tire tracks disappeared under Mount Everest flake at a 4.6% reading, a crowded garage reset in fine Rhino Grey flake, and a 629 square foot trash room in a residential building that now washes down with a hose. Browse the rest in our full portfolio.
An owner comes out, tests your slab, brings real color samples and writes a clear quote. No pressure, just a plan for a floor you'll only buy once.
We work all over Seattle. North of the Ship Canal that means Ballard, Fremont, Phinney Ridge, Greenwood, Green Lake, Wallingford, Ravenna, Maple Leaf, Wedgwood, View Ridge, Northgate and Lake City. In the middle of town, Queen Anne, Magnolia, Capitol Hill and Montlake. South and west, Beacon Hill, Columbia City, the Rainier Valley and West Seattle.
The housing changes block by block. Early 1900s Craftsman homes with detached alley garages. Hillside houses with the garage tucked underneath. Mid-century ramblers with attached two-car garages. New townhomes along the arterials with narrow tandem bays. We have coated all of those shapes, plus stairs, porches and commercial rooms.
Planning a bigger remodel first? Check permits with the City of Seattle, then let the floor go in after the drywall. If you live just outside the city, we also coat floors in Shoreline, Mercer Island, Bellevue and Renton.
Story one. You buy a weekend epoxy kit, scrub the slab and roll it on. It looks fine for a while. Then the spot under your tires lifts, the area by the door turns amber and white mineral rings push through from below. You empty the garage again, pay someone to grind it off and buy a second floor. Our post on the hidden cost of cheap coatings around Seattle lays it out.
Story two. Your slab is tested, ground, repaired and coated once. Rain, grit and oil wipe off a non-porous surface. The color holds. You stop thinking about the floor at all, which is the whole point of a 30 to 40 year floor.
Don't see yours? Call 425-226-6085 and an owner will answer it.
Yes. We install epoxy poly garage floors across Seattle using Certified Penntek polyurea instead of epoxy. It looks like a premium flake floor and offers up to 5x the lifespan of typical epoxy. See all our services or book a free in-home quote.
We do. The same Penntek system that protects garages works on outdoor concrete around Seattle, with a slip-resistant finish and FadeLock UV stability. See patio and walkway projects.
Yes. We coat shops, showrooms, clinics and service bays in and around Seattle. See our commercial projects.
Call 425-226-6085 or request a free in-home quote. An owner visits, tests your slab and brings color samples. We don't quote over the phone because every slab is different.
Honest note. We wrote this page so people in Seattle searching for epoxy garage floors and concrete coatings would find us. Then we filled it with real readings and real rooms from your city, because you deserve more than a sales pitch.
If your garage is under the house, behind it off the alley or attached to a brand-new townhome, we would be glad to come look. Call 425-226-6085 or book a free in-home quote.
Book a free in-home quote and we will test your concrete, measure the space and show you colors in your own light. Call 425-226-6085.