Certified Penntek dealer / Woodinville, WAServing Seattle & the EastsideLimited lifetime warranty
Cascade Concrete Coatings
425-226-6085Get a free quote
Medina Epoxy Poly Coated Garage Floors & Concrete Coatings

Considering Epoxy for Your Medina Garage? Here's a Better Path.

Medina homes are built with care, and the garage floor should be too. We test the slab, prep it properly and install Certified Penntek polyurea in a finish that suits the house.

✓Certified Penntek dealer✓Limited lifetime warranty✓Most garages done in one day
Medina garage floors

Most Medina homeowners want a garage floor that still looks new in twenty years. Finding one is hard, because a lot of epoxy installers rush the prep and roll on a coating that's built to be redone.

Don't get stuck redoing your floor every few years. We'll test your Medina slab, prep it right and install a Certified Penntek polyurea floor that bonds with your concrete, so you can stop worrying about the garage and start enjoying it.

The short answer

Cascade Concrete Coatings, a Certified Penntek Dealer, installs epoxy-style garage floor coatings in Medina using Penntek pure polyurea instead of epoxy. Every slab is moisture and hardness tested at a free in-home quote before any plan is made. Most garages are finished in one day, and every floor carries a limited lifetime warranty backed by Penntek. Our Medina project was a 420 square foot slab rated Poor that still qualified.

Real floors in and around MedinaSee all Medina projects →
4finished floors in and around Medina
Up to 5xthe lifespan of typical epoxy
30 to 40year floor, built to bond with your slab
1 dayinstall for a typical garage
The quiet problem

Your Home Is Finished. Is Your Garage Floor?

In Medina the house usually gets every bit of attention. Millwork, landscaping, lighting, a view of the lake. Then you open the garage and the slab tells a different story.

The Medina garage we coated had patches of old pink and red paint stuck to the concrete, rough uneven areas and a cut-in section of newer concrete from an earlier repair. An EV charger was mounted on a center post. The slab was rated Poor on the Penntek job card.

That's common in older homes around the Points. A few owners, a few projects, a few patches. Paint and thin coatings get added over the years, and none of it bonds to the concrete in a lasting way. It just piles up.

What we deliver

We'll turn your Medina garage into a floor you only buy once.

Every Medina job starts with a moisture and hardness test, then industrial diamond grinding, crack repair with Penntek Mender and a pure polyurea basecoat with a FadeLock UV topcoat. That's how we deliver up to 5x the lifespan of typical epoxy, a 30 to 40 year floor, with a limited lifetime warranty backed by Penntek.

Before and after

Same slab. Same angle. Night and day.

Drag the handle to compare. Every pair is a real floor our team ground, repaired and coated.

↔BeforeAfter
Commercial floor · Everett, WASolid Dark Grey Service Shop Floor in Everett1 of 12
Certified Penntek vs. typical epoxy or poly

Medina garage floors fail six ways. We beat all six.

The coating is only half of it. Watch the same slab go through what a Medina garage puts it through, once with typical epoxy or cheap poly and once the way we install Penntek.

The right system for your concrete

Your slab’s age, composition and moisture all matter. We test it first, then choose the Penntek system that fits, adding a moisture barrier when the readings call for it.

Moisture & hardness tested
Typical epoxy or cheap polySame slab
✕Moisture pushes up from the slab. Blisters and peeling follow.
Certified Penntek by CascadeSame slab
✓Tested first. A moisture barrier goes down when the slab needs one.
Score after round 1Certified Penntek 1, typical epoxy or poly 0
The Penntek advantage

Not all coatings are equal. Watch.

Side-by-side tests on the same slab, in the same conditions. Typical epoxy and cheap poly on one side, certified Penntek on the other.

Stain testOil, brake fluid and road grime wipe right off the non-porous Penntek topcoat, where typical epoxy can absorb stains.
Stretch testPenntek’s flexible basecoat stretches with the concrete. Brittle epoxy cracks and lets go.
Hammer testDropped tools are part of garage life. Typical coatings chip. Penntek resists chips and dents.
Watch the full side-by-side tests →

Settling for a quick epoxy job can leave your Medina garage peeling by year five.

A floor that fails doesn't just look bad. It means emptying the garage, grinding off the old coating and paying all over again.

✕Peeling where your tires sitSome installers skip diamond grinding, so the coating never truly grips your slab. Hot tires can lift it right off.
✕Yellowing by the garage doorMany epoxies amber in sunlight, so the first few feet of your floor turn a different color than the rest.
✕Cracks showing throughSome crews coat right over cracks. Every bit of slab movement shows up in your floor within a season or two.
✕Moisture blistersPuget Sound slabs hold moisture. Skip the testing and water vapor can push the coating up in bubbles.
✕Paying for it twiceTypical epoxy problems often show in years 3 to 5. Every redo means emptying your Medina garage and starting over.

We know your garage is more than a place to park. It's part of your home.

For a lot of Medina families it's the gym, the workshop, the mudroom and the first thing you see when you get home. You've put real money into it. You deserve a floor you never have to think about again, installed by people who treat your home like their own.

Nicole and Sheldon, owners of Cascade Concrete Coatings
The after

Picture pulling into a Medina garage you're proud of.

Here's what a Certified Penntek floor from our team gives you, long after install day.

✓Clean up in secondsThe non-porous topcoat shrugs off oil, salt and road grime, so a quick wipe keeps your garage looking finished.
✓Color that stays trueFadeLock UV stability keeps the floor by the open door matching the back wall, year after year.
✓A floor that moves with your slabThe flexible basecoat handles Northwest temperature swings and settling, so your Medina floor doesn't crack with the concrete.
✓Your garage back in a dayA typical garage is finished in one day. Before we leave, the crew gives you clear walk-on and parking times.
✓Coverage that outlasts any one shopYour limited lifetime warranty is backed by Penntek, the manufacturer, so it isn’t tied to one small company.
✓A garage that adds to your homeA finished, showroom-clean floor makes a strong first impression for guests, and for buyers when it’s time to sell.
Performance at every layer

Typical epoxy is one coat. Ours is a system.

Every certified Penntek floor is built in four layers, each doing its own job. Watch it go down layer by layer, then tap a layer to see what it does for your floor.

01020304

When moisture readings call for it, we add a two-layer moisture barrier system before the basecoat.

Why not epoxy

Why Your Medina Floor Deserves More Than Epoxy

Most homeowners start by looking up epoxy garage floors. It's the familiar word. What you probably want is the look: an even flake finish with a clean, glossy topcoat that's easy to keep up.

Typical epoxy is a stiff film with a mechanical grip. Lakeside air keeps slabs damp much of the year, and concrete expands and shrinks with the seasons. A brittle layer can't follow that movement. It cracks, lifts where tires sit and yellows where sunlight hits through the garage door windows.

Penntek is a proprietary pure polyurea blend, over 99% solids, that chemically bonds to diamond-ground concrete at 1,300+ PSI. It flexes instead of cracking. The polyaspartic topcoat is non-porous and resists hot tire pickup, oil, salt and chemicals. FadeLock™ UV stability passed a 16-hour QUV test, so a light grey stays light grey. Read more on why sunlight still matters for garage floors here.

Many people call it an epoxy poly garage floor. We think of it as the floor epoxy was trying to be. See the bond test on our live demo page.

01 / 04Pure polyurea, Penntek's own blendA proprietary pure polyurea basecoat at over 99% solids. It chemically bonds to ground concrete at 1,300+ PSI and moves with the slab, rather than cracking like a rigid film.
02 / 04Certified hands on your slabHighly trained certified installers handle the prep: industrial diamond grinding, paint removal, patch blending and Penntek Mender crack repair. A slab rated Poor can still become a warranted floor.
03 / 04Penntek stands behind itYour floor carries a limited lifetime warranty backed by Penntek, the manufacturer, not just by an installer. We review the terms with you at the quote.
04 / 04A better floor for the long runBuilt for 30 to 40 years and up to 5x the lifespan of typical epoxy. A Bond Stronger Than Concrete, as Penntek puts it, made to be done once.
Watch the side-by-side tests →How the Penntek warranty works →
Not your typical epoxy crew

Professionally trained installers

Anyone can buy a kit and call themselves a garage floor company. Penntek doesn't sell to just anyone. Our team was vetted, trained hands-on through Penntek Academy and is backed by Penntek's full-time technical support team from prep to finish. That's the Penntek Standard, on every floor we install.

Certified Penntek Dealer

What "Certified Penntek Dealer" actually means

  1. 01Vetted before trainingPenntek reviews every company first. Many never make it to training.
  2. 02Hands-on training at PenntekChemistry, slab analysis, prep, application and troubleshooting, taught by Penntek’s technical team.
  3. 03Exclusive formulasPenntek’s proprietary polyurea is sold only to certified dealers. You can’t buy it at a store.
  4. 04Backed on every jobPenntek’s technical support team backs our crew from prep to finish, and Penntek backs your floor’s limited lifetime warranty.
What we coat in Medina

Any concrete, inside or out.

Garages are most of what we do in Medina, but the same Penntek system protects patios, pool decks, basements and commercial floors.

Garage floorsEpoxy poly garage floors for Medina homes, from one-car to four-car.Patios & walkwaysWeather-ready, slip-resistant coatings for outdoor concrete.Pool decksA good-looking, durable finish around the water.BasementsMoisture-tested coatings for finished and unfinished basements.Commercial floorsShops, showrooms and clinics in and around Medina.
What to expect

A Simple Plan for Your Medina Garage

We keep it to three steps and keep your schedule in mind. The full detail is on the Penntek installation process page.

  1. 01Meet us at your garageBook a free in-home quote. We meter moisture, test hardness and look at paint, patches and cracks. You get readings and a written quote, with no pressure.
  2. 02One day of focused workWe grind, repair, coat and clean up, typically in a single day. On the way out the crew tells you when you can walk on it and park.
  3. 03Live with a finished garageBring the cars and gear home. Rinse away leaves and grit with ease. Your floor has a limited lifetime warranty backed by Penntek.
How we approach it

We Treat Your Slab Like the Rest of the House

Cascade Concrete Coatings is a Certified Penntek Dealer based in Woodinville, and we work up and down the Eastside shore of Lake Washington. We'd rather do one floor right than rush three.

On that Medina job the consultation was on a wet day in late March. We took two moisture readings, 4.5% and 4.6%, and ran a scratch test for hardness. In April, on install day, the slab read 4.1% at 55°F, with the air also at 55°F and 64.4% humidity. Those numbers guided the prep.

Then we did the work properly. Old paint ground off. Patches and the cut-in section blended in. Wall base coated 41 feet around. A slab rated Poor at the start ended up with a full limited lifetime warranty backed by Penntek.

See the full install process →
Is it right for you?

Is a Penntek floor right for your Medina home?

You're probably a great fit if any of these sound familiar.

Restrained finishes

Pick a Finish as Calm as Your House

Medina owners often prefer quiet floors. The garage we coated here went with Rhino Grey, a single-color 1/4 inch flake. No black or white chips jumping out, just an even grey with texture underfoot.

If you want a little more depth, Mount Everest brightens a garage and Silver Creek adds warmth. Smoke sits well beside dark cabinetry. Look through the Penntek color and style gallery and our article on the finishes available for Penntek floors, then we'll bring physical samples.

Mount EverestEvolution FlakeWhite and light grey flake that makes a garage feel bigger and brighter. Mount Everest suits Medina garages with wood or white interiors and lower-level spaces with little daylight.Silver CreekEvolution FlakeA deeper grey and brown flake with warmth. Silver Creek stays clean looking under fall leaves and damp tire tracks, and pairs well with natural wood and stone.SmokeEvolution FlakeGrey, black and white flake that hides dirt and tire marks. A strong choice next to dark cabinetry or charcoal trim in newer Medina homes.
See every color and system →
Medina and next door

See the Medina Floor, Plus a Few Just Over the Line

Medina is a small town, and we'll be honest: we have one finished garage here so far. Rather than pad the list, we've added nearby Bellevue floors that show the same care, just a few minutes south across SR 520.

If your slab is damp, the most extreme moisture case we've handled is out in Belfair near Hood Canal, where readings of 5.8% and 5.9% called for a layered moisture barrier under Lani Grey flake. Far from Medina, but it shows what we do when concrete runs wet. Every project lives on the Cascade portfolio.

Close-up of Rhino Grey flake polyurea garage floor in Medina with the Cascade van
MedinaOct 2026Rhino Grey Single-Color Flake Garage in Medina
A 420 square foot slab rated Poor, with old pink and red paint, patches and an EV charger on a center post. Readings of 4.5% and 4.6% shaped the prep. In April 2026 it became an even, single-color Rhino Grey flake floor with 41 feet of coated wall base.
See this project →
Reviews

Hear it from your neighbors.

All reviews →
Loading Google reviews…
Free in-home quote in Medina

Get the Medina garage floor everyone wishes they had.

An owner comes out, tests your slab, brings real color samples and writes a clear quote. No pressure, just a plan for a floor you'll only buy once.

Book my free quote425-226-6085
Around Medina

From Evergreen Point to the Points, Garages We Understand

Medina sits on the Lake Washington shore just northwest of downtown Bellevue, with Evergreen Point and the SR 520 bridge landing at its north end. Lots are large and wooded, and homes range from classic mid-century houses to new estates that replaced them. That mix shows up in the garages.

Older homes tend to have smaller attached garages with slabs that have been painted, patched or partly repoured over the decades. Newer builds often have multi-car garages, sometimes on a lower level, with EV chargers, built-in storage and polished interiors that make bare concrete look out of place. Our ideas for multi-car garages in Eastside homes might spark a few thoughts.

Big firs and maples mean leaves and needles blow in every fall, and lakeside humidity keeps them damp. A non-porous floor makes cleanup a quick sweep and rinse. We also work in the neighboring Points communities and nearby cities. See our pages for Bellevue, Kirkland to the north, Mercer Island across the water and Redmond.

For town background, the Medina article on Wikipedia is a good start, and the City of Medina site covers permits if your garage is part of a larger project.

Nearby we also serve
BellevueKirklandMercer IslandRedmondSeattle
Two outcomes

The Floor You Redo, or the Floor You Forget About

Go the quick route and you might get a nice-looking floor for a while. Then the parking spots lift, the front edge yellows and a damp patch starts to bubble. In a garage full of cars, cabinets and charging gear, redoing it is a real disruption. You also pay to remove the failed layer first.

Go the Penntek route and the garage just stays finished. The flake looks the same years on. Spills wipe off, tires don't leave marks and you stop thinking about the floor. It's built for 30 to 40 years and lasts up to 5x as long as typical epoxy.

Not all concrete coatings are equal, and the difference rarely shows on day one. It shows in year five, when one floor is peeling and the other still looks new. Penntek calls its product the longest-lifespan concrete coating with the lowest lifetime cost of ownership, and the reason is simple. You buy it once.

Our guide to mistakes to avoid when choosing a concrete coating is worth five minutes before you collect quotes from anyone, us included.

Medina questions

What Medina homeowners ask us

Don't see yours? Call 425-226-6085 and an owner will answer it.

What determines the cost of a garage floor in Medina?+
The cost of a Medina garage floor depends on square footage, how much old paint and patching has to be ground away, crack repair, wall base or steps, and whether moisture readings call for a barrier. A 420 square foot slab rated Poor needs more prep than a new one. The in-home quote is free.
Can a slab rated Poor still be coated in Medina?+
Yes, a slab rated Poor can still be coated in Medina. Our local garage was rated Poor, with old paint, patches and a cut-in repair. After grinding and repair it received a Rhino Grey flake floor with a limited lifetime warranty backed by Penntek.
Does lakeside moisture affect Medina garage slabs?+
Lakeside moisture can affect Medina garage slabs, so we test every one. Our local slab read 4.5% and 4.6% at the consult and 4.1% on install day. Higher readings get a two-layer moisture barrier system under the basecoat before the flake goes down.
Can you install in Medina during the rainy season?+
Yes, we install in Medina during the rainy season. The local consult was on a wet March day and the install followed in April at 55°F. On install day the crew checks slab moisture and temperature and gives you walk-on and parking times before leaving.
How long will the floor last?+
The floor is built to last 30 to 40 years, up to 5x the lifespan of typical epoxy. It carries a limited lifetime warranty backed by Penntek. The topcoat resists hot tires, oil and salt, so daily parking won't wear through it.
Is Penntek polyurea different from an epoxy floor?+
Yes, Penntek polyurea is different from an epoxy floor. Epoxy is rigid and grips the surface mechanically. Penntek is a pure polyurea blend over 99% solids that bonds chemically at 1,300+ PSI and flexes with the concrete. That's why people often call it an epoxy polyurea floor.
Can my Medina garage floor handle EVs and charging equipment?+
Yes, a Medina garage floor coated with Penntek handles EVs and charging equipment. Our local job had an EV charger on a center post, and the crew coated cleanly around it. The polyaspartic topcoat resists hot tire pickup, oil and chemicals.
Which colors hide leaves, needles and grit?+
Multi-tone flakes like Silver Creek and Smoke hide leaves, needles and grit between cleanings. Single-color Rhino Grey gives a calmer look that still disguises dust. Very light floors brighten a garage but show a bit more.
Do you serve all of Medina, including Evergreen Point?+
Yes, we serve all of Medina, including Evergreen Point and the lakefront, plus the nearby Points communities of Hunts Point and Yarrow Point and the Clyde Hill area. We're based in Woodinville and work across the Eastside, so scheduling a quote, a color visit or an install day is easy.
Is the install done in one day?+
Yes, a typical garage install is done in one day. Larger multi-car garages or slabs that need extra moisture layers can take longer. We'll tell you the timeline at your quote so you can plan around it.
Does Cascade Concrete Coatings install epoxy garage floors in Medina?+

Yes. We install epoxy poly garage floors across Medina using Certified Penntek polyurea instead of epoxy. It looks like a premium flake floor and offers up to 5x the lifespan of typical epoxy. See all our services or book a free in-home quote.

Do you coat patios, walkways and pool decks in Medina?+

We do. The same Penntek system that protects garages works on outdoor concrete around Medina, with a slip-resistant finish and FadeLock UV stability. See patio and walkway projects.

Do you handle commercial concrete coatings in Medina?+

Yes. We coat shops, showrooms, clinics and service bays in and around Medina. See our commercial projects.

How do I get a quote for my Medina garage floor?+

Call 425-226-6085 or request a free in-home quote. An owner visits, tests your slab and brings color samples. We don't quote over the phone because every slab is different.

Plainly put

Why We Wrote This for Medina

Plainly put, we wrote this page so people in Medina searching for epoxy garage floors and concrete coatings would find a Certified Penntek crew nearby. We only have one local floor to show so far, and we'd rather tell you that than dress it up.

Thanks for reading. If your garage floor is the one unfinished surface in the house, call 425-226-6085 or request your free in-home quote.

Nicole and Sheldon, owners

Ready for a Medina Garage Floor That Matches the House?

Call 425-226-6085 or set up a free in-home quote. We'll test the slab and bring samples to see in your own light.

Get my free quote425-226-6085
All 30 cities we serveService area overview →
Ames LakeBellevueBothellCarnationDuvallEdmondsEverettIssaquahKenmoreKentKirklandLake Forest ParkLake StevensLynnwoodMarysvilleMedinaMercer IslandMill CreekMonroeMount VernonMukilteoNewcastleRedmondRentonSammamishSeattleShorelineSnohomishStanwoodWoodinville