Certified Penntek dealer / Woodinville, WAServing Seattle & the EastsideLimited lifetime warranty
Cascade Concrete Coatings
425-226-6085Get a free quote
Kirkland Epoxy Poly Coated Garage Floors & Concrete Coatings

Kirkland Garage Floors, Past the Epoxy Kit Stage

From Juanita to Houghton, we grind, repair and coat Kirkland garage slabs with Certified Penntek polyurea. One day on site, tested before we quote, and built to outlast typical epoxy.

✓Certified Penntek dealer✓Limited lifetime warranty✓Most garages done in one day
Kirkland garage floors

Most Kirkland homeowners want a garage floor that still looks new in twenty years. Finding one is hard, because a lot of epoxy installers rush the prep and roll on a coating that's built to be redone.

Don't get stuck redoing your floor every few years. We'll test your Kirkland slab, prep it right and install a Certified Penntek polyurea floor that bonds with your concrete, so you can stop worrying about the garage and start enjoying it.

The short answer

Cascade Concrete Coatings, a Certified Penntek Dealer based in Woodinville, installs epoxy-style garage floor coatings in Kirkland using Penntek pure polyurea instead of epoxy. Every slab gets moisture and hardness testing at a free in-home quote. A typical garage is ground, crack repaired and coated in one day, with a limited lifetime warranty backed by Penntek. Ten Kirkland floors are documented in the portfolio.

Real floors in and around KirklandSee all Kirkland projects →
11finished floors in and around Kirkland
Up to 5xthe lifespan of typical epoxy
30 to 40year floor, built to bond with your slab
1 dayinstall for a typical garage
The Kirkland garage problem

Your Garage Is Probably the Only Unfinished Room in Your House

Walk through most homes in town and every room looks done except one. The garage still has bare grey concrete with tire lanes, drip spots by the door and a dusty film that tracks inside on your shoes.

Then the rain shows up. From October to May, cars roll in off I-405 and NE 85th carrying road grit and water. Bare concrete is porous, so it drinks all of it. Oil stains spread. Leaves blow under the door from the big firs on Finn Hill and Rose Hill and get ground into the surface.

Lots of people try an epoxy kit or a coat of floor paint first. We have stripped both off Kirkland slabs. One family garage had grey paint peeling away in big patches before our crew ground it down and coated it in Slate Stone. A thin film sitting on top of damp concrete just doesn't hold.

What we deliver

We'll turn your Kirkland garage into a floor you only buy once.

Every Kirkland job starts with a moisture and hardness test, then industrial diamond grinding, crack repair with Penntek Mender and a pure polyurea basecoat with a FadeLock UV topcoat. That's how we deliver up to 5x the lifespan of typical epoxy, a 30 to 40 year floor, with a limited lifetime warranty backed by Penntek.

Kirkland before and after

Real Kirkland floors, before and after.

Drag the handle to compare. Every pair is a real floor our team ground, repaired and coated.

↔BeforeAfter
Certified Penntek vs. typical epoxy or poly

Kirkland garage floors fail six ways. We beat all six.

The coating is only half of it. Watch the same slab go through what a Kirkland garage puts it through, once with typical epoxy or cheap poly and once the way we install Penntek.

The right system for your concrete

Your slab’s age, composition and moisture all matter. We test it first, then choose the Penntek system that fits, adding a moisture barrier when the readings call for it.

Moisture & hardness tested
Typical epoxy or cheap polySame slab
✕Moisture pushes up from the slab. Blisters and peeling follow.
Certified Penntek by CascadeSame slab
✓Tested first. A moisture barrier goes down when the slab needs one.
Score after round 1Certified Penntek 1, typical epoxy or poly 0
The Penntek advantage

Not all coatings are equal. Watch.

Side-by-side tests on the same slab, in the same conditions. Typical epoxy and cheap poly on one side, certified Penntek on the other.

Stain testOil, brake fluid and road grime wipe right off the non-porous Penntek topcoat, where typical epoxy can absorb stains.
Stretch testPenntek’s flexible basecoat stretches with the concrete. Brittle epoxy cracks and lets go.
Hammer testDropped tools are part of garage life. Typical coatings chip. Penntek resists chips and dents.
Watch the full side-by-side tests →

Settling for a quick epoxy job can leave your Kirkland garage peeling by year five.

A floor that fails doesn't just look bad. It means emptying the garage, grinding off the old coating and paying all over again.

✕Peeling where your tires sitSome installers skip diamond grinding, so the coating never truly grips your slab. Hot tires can lift it right off.
✕Yellowing by the garage doorMany epoxies amber in sunlight, so the first few feet of your floor turn a different color than the rest.
✕Cracks showing throughSome crews coat right over cracks. Every bit of slab movement shows up in your floor within a season or two.
✕Moisture blistersPuget Sound slabs hold moisture. Skip the testing and water vapor can push the coating up in bubbles.
✕Paying for it twiceTypical epoxy problems often show in years 3 to 5. Every redo means emptying your Kirkland garage and starting over.

We know your garage is more than a place to park. It's part of your home.

For a lot of Kirkland families it's the gym, the workshop, the mudroom and the first thing you see when you get home. You've put real money into it. You deserve a floor you never have to think about again, installed by people who treat your home like their own.

Nicole and Sheldon, owners of Cascade Concrete Coatings
The after

Picture pulling into a Kirkland garage you're proud of.

Here's what a Certified Penntek floor from our team gives you, long after install day.

✓Clean up in secondsThe non-porous topcoat shrugs off oil, salt and road grime, so a quick wipe keeps your garage looking finished.
✓Color that stays trueFadeLock UV stability keeps the floor by the open door matching the back wall, year after year.
✓A floor that moves with your slabThe flexible basecoat handles Northwest temperature swings and settling, so your Kirkland floor doesn't crack with the concrete.
✓Your garage back in a dayA typical garage is finished in one day. Before we leave, the crew gives you clear walk-on and parking times.
✓Coverage that outlasts any one shopYour limited lifetime warranty is backed by Penntek, the manufacturer, so it isn’t tied to one small company.
✓A garage that adds to your homeA finished, showroom-clean floor makes a strong first impression for guests, and for buyers when it’s time to sell.
Performance at every layer

Typical epoxy is one coat. Ours is a system.

Every certified Penntek floor is built in four layers, each doing its own job. Watch it go down layer by layer, then tap a layer to see what it does for your floor.

01020304

When moisture readings call for it, we add a two-layer moisture barrier system before the basecoat.

Epoxy or polyurea?

Why Your Kirkland Slab Needs More Than Epoxy

Most people start by searching epoxy garage floors, and that's fine. The look you want, a flake floor with a glossy topcoat, is the same. What's underneath is not.

Typical epoxy is a rigid film that grips the surface. Kirkland slabs move with the seasons and many of the older ones on the hills were poured without a vapor barrier, so water vapor pushes up from below. A stiff film cracks, lifts at the tire lanes and yellows near the door. That's the failure most people tell us about.

What we install gets called epoxy poly garage floors a lot, because the steps look alike. The product is Penntek's proprietary pure polyurea blend, over 99% solids, with a 1,300+ PSI chemical bond to ground concrete. The polyaspartic topcoat is non-porous and shrugs off hot tire pickup, oil and road salt. FadeLock™ UV stability passed a 16-hour QUV test, which matters with all the glass garage doors going into new Kirkland homes.

Penntek calls it A Bond Stronger Than Concrete. You can watch the bond and flex tests side by side on the side-by-side epoxy vs Penntek demo.

01 / 04A pure polyurea blendPenntek's proprietary pure polyurea basecoat is over 99% solids and flexes as Kirkland slabs shift through wet winters and dry summers, where a rigid epoxy film tends to crack and let go.
02 / 04Certified, trained installersOur crew is trained and certified by Penntek. They diamond grind every slab, repair cracks with Penntek Mender and add a moisture barrier when your readings call for one. Prep is where floors win or fail.
03 / 04A warranty Penntek stands behindYour floor carries a limited lifetime warranty backed by Penntek, the manufacturer. That means the promise isn't riding on one small company alone. Ask us to walk through the terms at your quote.
04 / 04A better floor, start to finishUp to 5x the lifespan of typical epoxy and built for 30 to 40 years. Penntek calls it the longest-lifespan concrete coating with the lowest lifetime cost of ownership.
Watch the side-by-side tests →How the Penntek warranty works →
Not your typical epoxy crew

Professionally trained installers

Anyone can buy a kit and call themselves a garage floor company. Penntek doesn't sell to just anyone. Our team was vetted, trained hands-on through Penntek Academy and is backed by Penntek's full-time technical support team from prep to finish. That's the Penntek Standard, on every floor we install.

Certified Penntek Dealer

What "Certified Penntek Dealer" actually means

  1. 01Vetted before trainingPenntek reviews every company first. Many never make it to training.
  2. 02Hands-on training at PenntekChemistry, slab analysis, prep, application and troubleshooting, taught by Penntek’s technical team.
  3. 03Exclusive formulasPenntek’s proprietary polyurea is sold only to certified dealers. You can’t buy it at a store.
  4. 04Backed on every jobPenntek’s technical support team backs our crew from prep to finish, and Penntek backs your floor’s limited lifetime warranty.
What we coat in Kirkland

Any concrete, inside or out.

Garages are most of what we do in Kirkland, but the same Penntek system protects patios, pool decks, basements and commercial floors.

Garage floorsEpoxy poly garage floors for Kirkland homes, from one-car to four-car.Patios & walkwaysWeather-ready, slip-resistant coatings for outdoor concrete.Pool decksA good-looking, durable finish around the water.BasementsMoisture-tested coatings for finished and unfinished basements.Commercial floorsShops, showrooms and clinics in and around Kirkland.
The plan

Three Steps From Grey Slab to Finished Garage

No pressure and no surprises. Here is how a project runs from first call to parking the car. The full walk-through lives on our installation process page.

  1. 01We test your slab firstBook a free in-home quote. We meter moisture in more than one spot, scratch test hardness, check cracks and old coatings, then hand you a clear written quote.
  2. 02We grind and coat in a dayClear the garage and we handle the rest. Diamond grinding, crack repair, basecoat, flake and topcoat, usually done by evening. Before leaving, the crew gives you walk-on and parking times.
  3. 03You park on it for decadesMove the bikes, bins and car back in. Hose it off after a muddy week. Your floor is covered by a limited lifetime warranty backed by Penntek.
Why we're a good fit

You Want a Floor That's Done Once. That's How We Work.

We are Cascade Concrete Coatings, a Certified Penntek Dealer out of Woodinville, roughly six miles up the road. Kirkland is one of the places we work most, and our concrete coatings portfolio shows it.

We don't quote from a photo. At your free in-home quote we meter the slab for moisture, scratch test it for hardness and look for cracks, old paint and anything the grinder will need to deal with. Around town we have read anywhere from 2.0% on an older two-bay to 5.1% on a newer garage with a trench drain. Those numbers decide how your floor gets built.

Then a trained crew does the work. They diamond grind, fill cracks with Penntek Mender, add a two-layer moisture barrier system if the readings call for it, and put down the pure polyurea basecoat, flake and topcoat. Most garages are finished the same day.

See the full install process →
Is it right for you?

Is a Penntek floor right for your Kirkland home?

You're probably a great fit if any of these sound familiar.

Colors that work here

Pick a Flake That Forgives Kirkland Weather

Grey-based blends are the local favorite for flake concrete coatings, and for good reason. They hide wet tire tracks, needle litter and the fine grit that comes in on every car. Slate Stone has been picked twice in town, and Smoke made a cracked two-bay look brand new.

Lighter blends brighten a long, dim garage. Darker ones forgive a busy family space. Bring a sample board out to the driveway and hold it next to your siding and cabinets. Browse the full color and style library to narrow it down before we visit.

Slate StoneEvolution FlakeThe most picked flake in Kirkland so far, chosen twice. Slate Stone mixes grey, tan and black, so muddy tire tracks and fir needles disappear into it between cleanings.Silver CreekEvolution FlakeA deeper grey and brown that suits modern homes with dark trim and concrete accents. Silver Creek stays clean looking in a long tandem garage that sees a lot of traffic.Tidal WaveEvolution FlakeCascade's most installed color, a blue-grey, white and black flake. It feels at home a few blocks from the lake and pairs well with white walls and black garage doors.SmokeEvolution FlakeGrey, black and white flake that hides dirt and tire marks. Smoke is a strong pick for older Kirkland slabs with repaired cracks, since the pattern blends the repair lines in completely.
See every color and system →
Proof on Kirkland slabs

See Floors We've Finished Near You

Kirkland garages come in every shape. Long tandem bays, narrow rooms with a furnace in the back, brand-new builds with nothing in them yet. Each one below started with a moisture reading and ended with a floor that cleans up with a hose and a squeegee.

A few more worth a look: a garage with red and mint cabinets that got 506 square feet of Comet flake plus coated stem walls on a 50°F November day, and a brand-new build coated in Stoney Creek before a single box moved in. You can browse every job in the full project portfolio.

More floors in and around Kirkland

See all Kirkland projects →
Hunts Point garage with maple cabinets, slatwall and a Limestone polyurea floorHunts PointLimestone Hybrid Flake Garage Floor in Hunts PointWild Dove flake floor coating around furnace base in a Kirkland garageKirklandWild Dove Flake Garage Floor in KirklandComet flake polyurea garage floor beside red wall cabinets in a Kirkland garageKirklandComet Flake Garage Floor With Red Cabinets in KirklandClose view of Stoney Creek flake polyurea texture in a Kirkland garageKirklandStoney Creek Flake New-Build Garage in KirklandSlate Stone Evolution garage floor coating in Kirkland, WA by Cascade Concrete CoatingsKirklandSlate Stone Flake Family Garage in Kirkland
Reviews

Hear it from your neighbors.

All reviews →
Loading Google reviews…
Free in-home quote in Kirkland

Get the Kirkland garage floor everyone wishes they had.

An owner comes out, tests your slab, brings real color samples and writes a clear quote. No pressure, just a plan for a floor you'll only buy once.

Book my free quote425-226-6085
Around Kirkland

Your Neighborhood, Your Kind of Garage

We have coated floors all over town, and the garages change as you move around. Older split-levels in Juanita and on Finn Hill often have tuck-under garages with low slabs, block stem walls and decades of stains. Houghton and the Lakeview area near the water mix older homes with tear-down rebuilds that come with slick trowel finishes and drywall mud on the concrete. Totem Lake and Rose Hill have plenty of newer two-car garages that are still clean enough to coat before the damage starts.

Down by Moss Bay and Marina Park, lots are tighter and garages often double as bike and paddleboard storage. One of our customers keeps a kayak hanging right over the parking spot. Up in Bridle Trails, bigger lots mean bigger garages and longer days for the crew, but still one visit for most jobs.

We also work just across the city lines. Neighbors in Redmond garages over the hill, Bellevue to the south, Kenmore at the north end of the lake and Woodinville, where we're based get the same crew and the same testing. Want city history? The Kirkland Wikipedia entry covers it, and the City of Kirkland website has permit info if your garage project is part of a bigger remodel.

Nearby we also serve
RedmondBellevueMedinaKenmoreWoodinvilleBothell
Two ways this can go

Cheap Kit Now, or One Floor for Decades

Here is the cheap way. You roll on an epoxy kit over a weekend. It looks great for a year or two. Then hot tires lift it in the parking lanes, the area near the door turns amber and moisture starts pushing up bubbles. Now you are emptying the garage again and paying someone to grind off the failed coating before anything new can go down.

Here is the other way. You clear the garage once. A crew grinds, repairs and coats it in a day. On a wet January evening you pull in, the drips sit on top of the surface and a quick wipe takes care of them. Ten years later the flake still looks the same. Penntek floors are built for 30 to 40 years, up to 5x the lifespan of typical epoxy.

Our post on whether a one-day coating is worth it in Kirkland lays out the math, and our look at how the Lake Washington climate treats garage floors explains why damp slabs need a real system.

Kirkland questions

What Kirkland homeowners ask us

Don't see yours? Call 425-226-6085 and an owner will answer it.

What affects the cost of a garage floor coating in Kirkland?+
The cost of a garage floor coating here depends on square footage, how much grinding the surface needs, the number of cracks to repair, any old paint or epoxy that has to come off, and whether moisture readings call for a barrier. Steps and stem walls add a little too. The in-home quote is free and you get the number in writing before anything is scheduled.
Do Kirkland garage slabs have moisture problems?+
Some local garage slabs do carry extra moisture, which is why we test every one. Across town we have read from 2.0% to 5.1%. Older homes on the hills may lack a vapor barrier, and new builds can still hold water from the pour. Higher readings get the two-layer moisture barrier system before the flake goes down.
Can you coat a Kirkland garage floor in the winter?+
Yes, we coat garage floors in Kirkland year round. One Slate Stone floor went down in December and a Comet floor on a 50°F November day. On install day the crew checks slab moisture and temperature and gives you walk-on and parking times before they leave. Our article on coating concrete in winter covers the details.
How long will a Penntek floor last in my Kirkland garage?+
A Penntek floor in your garage is built to last 30 to 40 years, up to 5x the lifespan of typical epoxy. It is covered by a limited lifetime warranty backed by Penntek. The polyaspartic topcoat resists oil, salt and hot tires, so normal daily parking won't wear through it.
Is polyurea really different from an epoxy floor?+
Yes, polyurea is a different material from epoxy, even though the install steps look similar. Typical epoxy is a rigid film. Penntek's pure polyurea basecoat is over 99% solids, flexes with the concrete and forms a 1,300+ PSI chemical bond. That's why many people call it an epoxy polyurea floor but treat it as the upgrade.
Will the coating handle my EV and a home workshop?+
Yes, the coating handles EVs and workshop use well. The polyaspartic topcoat is non-porous and resists hot tire pickup, oil, salt and most garage chemicals. Heavy EVs, rolling tool chests and dropped wrenches are all normal use. Spills wipe up instead of soaking into the concrete.
Which colors hide needles, mud and road grit in Kirkland?+
Multi-tone grey flakes do the most to hide needles, mud and road grit. Slate Stone, Smoke and Flint are favorites here because they break up dirt and tire marks. Very light or solid colors look sharp but show more between cleanings. We bring sample boards to your quote.
Do you serve my part of Kirkland?+
Yes, we serve every part of Kirkland, including Juanita, Finn Hill, Totem Lake, Rose Hill, Houghton, Lakeview, Moss Bay, Norkirk and Bridle Trails. We are based in Woodinville, a short drive north, so scheduling a quote anywhere in town is easy.
Is it really done in one day?+
Yes, a typical two-car garage is done in one day. The crew grinds, repairs cracks, applies the basecoat, flake and topcoat, and cleans up the same visit. Very large spaces or slabs that need extra moisture layers can take longer, and we tell you that at the quote.
What does the warranty on a Kirkland floor cover?+
Every floor we install carries a limited lifetime warranty backed by Penntek, the manufacturer. It isn't only our promise. We walk you through the exact terms at your free in-home quote, and our post on what lifetime coverage really means compares it with typical coverage.
Does Cascade Concrete Coatings install epoxy garage floors in Kirkland?+

Yes. We install epoxy poly garage floors across Kirkland using Certified Penntek polyurea instead of epoxy. It looks like a premium flake floor and offers up to 5x the lifespan of typical epoxy. See all our services or book a free in-home quote.

Do you coat patios, walkways and pool decks in Kirkland?+

We do. The same Penntek system that protects garages works on outdoor concrete around Kirkland, with a slip-resistant finish and FadeLock UV stability. See patio and walkway projects.

Do you handle commercial concrete coatings in Kirkland?+

Yes. We coat shops, showrooms, clinics and service bays in and around Kirkland. See our commercial projects.

How do I get a quote for my Kirkland garage floor?+

Call 425-226-6085 or request a free in-home quote. An owner visits, tests your slab and brings color samples. We don't quote over the phone because every slab is different.

A quick honest note

Why This Page Exists

We wrote this page so people in Kirkland searching for epoxy garage floors and concrete coatings would find us. That's the plain truth. Since you made it this far, we wanted it to be worth your time, so it's built from real Kirkland slabs and real readings instead of filler.

Glad you're here. If your garage is the last unfinished room in the house, give us a call at 425-226-6085 or book a free in-home quote.

Nicole and Sheldon, owners

Ready to Finish the Last Room in Your Kirkland Home?

Call 425-226-6085 or book a free in-home quote. We'll test your slab, show you real flake samples and give you a clear plan.

Get my free quote425-226-6085
All 30 cities we serveService area overview →
Ames LakeBellevueBothellCarnationDuvallEdmondsEverettIssaquahKenmoreKentKirklandLake Forest ParkLake StevensLynnwoodMarysvilleMedinaMercer IslandMill CreekMonroeMount VernonMukilteoNewcastleRedmondRentonSammamishSeattleShorelineSnohomishStanwoodWoodinville