Certified Penntek dealer / Woodinville, WAServing Seattle & the EastsideLimited lifetime warranty
Cascade Concrete Coatings
425-226-6085Get a free quote
Kenmore Epoxy Poly Coated Garage Floors & Concrete Coatings

Kenmore Epoxy Garage Floors, Built for the Way You Use Yours

Saws and planers, kayaks and bikes, two cars and a freezer. Kenmore garages work hard. We test your slab, repair the cracks and coat it in one day with Certified Penntek polyurea.

✓Certified Penntek dealer✓Limited lifetime warranty✓Most garages done in one day
Kenmore garage floors

Most Kenmore homeowners want a garage floor that still looks new in twenty years. Finding one is hard, because a lot of epoxy installers rush the prep and roll on a coating that's built to be redone.

Don't get stuck redoing your floor every few years. We'll test your Kenmore slab, prep it right and install a Certified Penntek polyurea floor that bonds with your concrete, so you can stop worrying about the garage and start enjoying it.

The short answer

Cascade Concrete Coatings, a Certified Penntek Dealer based in nearby Woodinville, installs epoxy-style garage floor coatings in Kenmore. Instead of epoxy, the floor is Certified Penntek polyurea: a pure polyurea basecoat over 99% solids, chemically bonded at over 1,300 PSI, under a polyaspartic topcoat. Your free in-home quote includes moisture and hardness testing, most garages are done in one day, and Penntek backs the floor with a limited lifetime warranty.

Real floors in and around KenmoreSee all Kenmore projects →
4finished floors in and around Kenmore
Up to 5xthe lifespan of typical epoxy
30 to 40year floor, built to bond with your slab
1 dayinstall for a typical garage
The working garage

Is Your Kenmore Garage a Shop First and a Parking Spot Second?

Plenty of them are. Kenmore sits at the north end of Lake Washington where the Sammamish River flows in, and people here tend to own things that need a garage. Kayaks and paddleboards. Bikes for the Burke-Gilman Trail. Table saws, planers and rolling tool carts. Sometimes a car fits in there too.

All that work shows up on the concrete. Sawdust gets ground into every pore. Oil, stain and finish drips soak in near the bench. A crack that started small runs across the middle and branches near the door, because many slabs here were poured on sloped lots decades ago. Sweeping just moves the dust around.

A thin epoxy garage floor is a poor match for that kind of use. It is brittle, so a dropped clamp or a crack in the slab can chip it. It grips only the surface, so oil-soaked concrete lets go of it. And it yellows near the open door.

The fix is not a thicker coat of the same thing. It is a concrete coating that bonds into ground concrete and flexes with the slab, put down by people who test before they touch it.

What we deliver

We'll turn your Kenmore garage into a floor you only buy once.

Every Kenmore job starts with a moisture and hardness test, then industrial diamond grinding, crack repair with Penntek Mender and a pure polyurea basecoat with a FadeLock UV topcoat. That's how we deliver up to 5x the lifespan of typical epoxy, a 30 to 40 year floor, with a limited lifetime warranty backed by Penntek.

Before and after

Same slab. Same angle. Night and day.

Drag the handle to compare. Every pair is a real floor our team ground, repaired and coated.

↔BeforeAfter
Commercial floor · Everett, WASolid Dark Grey Service Shop Floor in Everett1 of 12
Certified Penntek vs. typical epoxy or poly

Kenmore garage floors fail six ways. We beat all six.

The coating is only half of it. Watch the same slab go through what a Kenmore garage puts it through, once with typical epoxy or cheap poly and once the way we install Penntek.

The right system for your concrete

Your slab’s age, composition and moisture all matter. We test it first, then choose the Penntek system that fits, adding a moisture barrier when the readings call for it.

Moisture & hardness tested
Typical epoxy or cheap polySame slab
✕Moisture pushes up from the slab. Blisters and peeling follow.
Certified Penntek by CascadeSame slab
✓Tested first. A moisture barrier goes down when the slab needs one.
Score after round 1Certified Penntek 1, typical epoxy or poly 0
The Penntek advantage

Not all coatings are equal. Watch.

Side-by-side tests on the same slab, in the same conditions. Typical epoxy and cheap poly on one side, certified Penntek on the other.

Stain testOil, brake fluid and road grime wipe right off the non-porous Penntek topcoat, where typical epoxy can absorb stains.
Stretch testPenntek’s flexible basecoat stretches with the concrete. Brittle epoxy cracks and lets go.
Hammer testDropped tools are part of garage life. Typical coatings chip. Penntek resists chips and dents.
Watch the full side-by-side tests →

Settling for a quick epoxy job can leave your Kenmore garage peeling by year five.

A floor that fails doesn't just look bad. It means emptying the garage, grinding off the old coating and paying all over again.

✕Peeling where your tires sitSome installers skip diamond grinding, so the coating never truly grips your slab. Hot tires can lift it right off.
✕Yellowing by the garage doorMany epoxies amber in sunlight, so the first few feet of your floor turn a different color than the rest.
✕Cracks showing throughSome crews coat right over cracks. Every bit of slab movement shows up in your floor within a season or two.
✕Moisture blistersPuget Sound slabs hold moisture. Skip the testing and water vapor can push the coating up in bubbles.
✕Paying for it twiceTypical epoxy problems often show in years 3 to 5. Every redo means emptying your Kenmore garage and starting over.

We know your garage is more than a place to park. It's part of your home.

For a lot of Kenmore families it's the gym, the workshop, the mudroom and the first thing you see when you get home. You've put real money into it. You deserve a floor you never have to think about again, installed by people who treat your home like their own.

Nicole and Sheldon, owners of Cascade Concrete Coatings
The after

Picture pulling into a Kenmore garage you're proud of.

Here's what a Certified Penntek floor from our team gives you, long after install day.

✓Clean up in secondsThe non-porous topcoat shrugs off oil, salt and road grime, so a quick wipe keeps your garage looking finished.
✓Color that stays trueFadeLock UV stability keeps the floor by the open door matching the back wall, year after year.
✓A floor that moves with your slabThe flexible basecoat handles Northwest temperature swings and settling, so your Kenmore floor doesn't crack with the concrete.
✓Your garage back in a dayA typical garage is finished in one day. Before we leave, the crew gives you clear walk-on and parking times.
✓Coverage that outlasts any one shopYour limited lifetime warranty is backed by Penntek, the manufacturer, so it isn’t tied to one small company.
✓A garage that adds to your homeA finished, showroom-clean floor makes a strong first impression for guests, and for buyers when it’s time to sell.
Performance at every layer

Typical epoxy is one coat. Ours is a system.

Every certified Penntek floor is built in four layers, each doing its own job. Watch it go down layer by layer, then tap a layer to see what it does for your floor.

01020304

When moisture readings call for it, we add a two-layer moisture barrier system before the basecoat.

The real difference

Epoxy Cracks. Here Is What You Get Instead.

People in Kenmore search for an epoxy floor, and a lot of them call our work epoxy poly garage floors once they see it go in. That is fine by us. What you get is Certified Penntek polyurea, and four things set it apart when they work together.

1. A proprietary pure polyurea blend. Over 99% solids, flexible and available only through certified dealers. It moves with a cracked slab instead of breaking over it.

2. Prep by highly trained certified installers. Industrial diamond grinding cuts out ground-in sawdust and oil. Penntek Mender fills the cracks.

3. A limited lifetime warranty backed by Penntek. The manufacturer, in 200+ markets, stands behind your floor.

4. A better product overall. A 1,300+ PSI chemical bond, a non-porous polyaspartic topcoat that resists hot tire pickup, oil, salt and chemicals, and FadeLock™ UV stability proven in a 16-hour QUV test. That adds up to up to 5x the lifespan of typical epoxy. See it on our live coating demo or read why epoxy fails on local slabs.

01 / 04The proprietary blendPenntek's pure polyurea is over 99% solids and only certified dealers install it. Flexible enough to ride over slab movement, tough enough for rolling tool chests and dropped hardware.
02 / 04Certified prep, every timeHighly trained certified installers diamond grind the concrete and fill cracks with Penntek Mender. Sawdust, finish stains and oil come out with the top layer, so the coating bonds to sound concrete.
03 / 04Manufacturer-backed coverageA limited lifetime warranty backed by Penntek covers your floor. That backing comes from the manufacturer itself, so it does not hinge on one small installer staying around.
04 / 04A better product, start to finishA Bond Stronger Than Concrete. Up to 5x the lifespan of typical epoxy, a topcoat that resists hot tire pickup and chemicals, and a 30 to 40 year floor.
Watch the side-by-side tests →How the Penntek warranty works →
Not your typical epoxy crew

Professionally trained installers

Anyone can buy a kit and call themselves a garage floor company. Penntek doesn't sell to just anyone. Our team was vetted, trained hands-on through Penntek Academy and is backed by Penntek's full-time technical support team from prep to finish. That's the Penntek Standard, on every floor we install.

Certified Penntek Dealer

What "Certified Penntek Dealer" actually means

  1. 01Vetted before trainingPenntek reviews every company first. Many never make it to training.
  2. 02Hands-on training at PenntekChemistry, slab analysis, prep, application and troubleshooting, taught by Penntek’s technical team.
  3. 03Exclusive formulasPenntek’s proprietary polyurea is sold only to certified dealers. You can’t buy it at a store.
  4. 04Backed on every jobPenntek’s technical support team backs our crew from prep to finish, and Penntek backs your floor’s limited lifetime warranty.
What we coat in Kenmore

Any concrete, inside or out.

Garages are most of what we do in Kenmore, but the same Penntek system protects patios, pool decks, basements and commercial floors.

Garage floorsEpoxy poly garage floors for Kenmore homes, from one-car to four-car.Patios & walkwaysWeather-ready, slip-resistant coatings for outdoor concrete.Pool decksA good-looking, durable finish around the water.BasementsMoisture-tested coatings for finished and unfinished basements.Commercial floorsShops, showrooms and clinics in and around Kenmore.
The plan

What Happens After You Call Us

It is a short list. For the step-by-step version with photos, visit our installation process page.

  1. 01Free quote, real readingsWe visit your Kenmore home, read moisture next to every crack, scratch test the slab and measure. You get a written quote with no pressure.
  2. 02One install dayDiamond grinding, Mender crack repair, the polyurea basecoat, flake and topcoat. Typical garages finish in one day, and we tell you when to walk and park.
  3. 03Back to your projectsMove the tools back and get to work. Spills wipe up, and your floor carries a limited lifetime warranty backed by Penntek.
Your crew

A Certified Crew a Few Miles Up the Road

Cascade Concrete Coatings is a Certified Penntek Dealer based in Woodinville, a few miles east along SR 522. Kenmore is close to home for us. We grind, test, repair and install one system, and we stand behind it with a warranty backed by the manufacturer.

Your project starts with a free in-home quote. We set a moisture meter down in several spots, including right next to any crack, because that is where water likes to travel. On the Kenmore woodshop garage, the reading beside the crack was 4.1%. We scratch test for hardness, measure the room and talk about how you actually use it.

If a slab reads high, we install a two-layer moisture barrier system before the polyurea. If it is ready, your garage is typically finished in one day, tools back on the wall by evening.

People here often ask about more than the garage. Boat and kayak storage pads, covered patios near the lake and basement shops all take the same concrete coatings. Ask us to look at those slabs on the same visit and we will test them too.

See the full install process →
Is it right for you?

Is a Penntek floor right for your Kenmore home?

You're probably a great fit if any of these sound familiar.

Choosing color

Picking a Color That Forgives Sawdust and Grit

A shop floor should hide the mess between cleanups. The Kenmore woodshop chose Tidal Wave, a busy blue-gray blend that keeps sawdust and trail grit from jumping out. Next door in Woodinville, two garages went with Domino for a crisp black and white look. See them all on the full color chart.

Tidal WaveEvolution FlakeThe Kenmore woodshop's pick and Cascade's most installed color. Blue-gray, white and black flake hides sawdust, trail grit from bikes and wet tire tracks between sweeps.SmokeEvolution FlakeA mid-gray flake that suits a garage under the house on a sloped Kenmore lot. It hides oil shadows and dark grime without making a dim room feel darker.Mount EverestEvolution FlakeLight white and gray flake for a garage you want bright. Great for a shop where you need to spot a dropped screw, and it opens up a tight single bay.DominoEvolution FlakeA bold black and white blend chosen for two Woodinville garages next door. It looks sharp with dark cabinets and hides a mix of light dust and dark spots.
See every color and system →
Proof

One Kenmore Workshop and Three Floors Next Door

Here is where we stand. We have one published floor inside Kenmore, the woodworker's garage below. To give you a fuller picture, we added three garages just over the line in Bothell and Woodinville, and we tell you which town each one is in.

Together they show the range: a busy shop, a single bay packed with bikes, a plain two-car garage done one week after testing and a pair of garages finished in one matching color. You can browse many more in our portfolio of finished floors.

Reviews

Hear it from your neighbors.

All reviews →
Loading Google reviews…
Free in-home quote in Kenmore

Get the Kenmore garage floor everyone wishes they had.

An owner comes out, tests your slab, brings real color samples and writes a clear quote. No pressure, just a plan for a floor you'll only buy once.

Book my free quote425-226-6085
Around Kenmore

Inglewood, Uplake, Moorlands: Your Corner of the North Lake

We work in every part of Kenmore. Downtown along Bothell Way near the river and Log Boom Park. Up the hills in Inglewood, Moorlands, Arrowhead and Uplake. Out along Juanita Drive toward Saint Edward State Park, where homes sit in the trees with long views of the lake.

Housing here runs from older split-levels and ramblers with attached two-car garages to newer homes and townhomes near downtown. Sloped lots are common, so many garages sit partly below the house. Those slabs tend to stay damper, which is why we read moisture next to every crack. You can read more about the city on Wikipedia, and if your floor is part of a bigger remodel, the City of Kenmore covers permits.

We also install floors right around you in Bothell, Lake Forest Park, Woodinville and Kirkland.

Nearby we also serve
BothellLake Forest ParkWoodinvilleShorelineLynnwoodKirkland
Choose once

Your Tools Deserve Better Than a Peeling Floor

A peeling floor in a workshop is a special kind of headache. Flakes of old epoxy get into your projects. Rolling carts catch on lifted edges. And when it finally has to be ground off, every tool, cabinet and machine has to come out of the garage. That is a weekend you will not get back.

Get it right once and the shop becomes easier to keep. Sawdust sweeps off a smooth, non-porous floor. Finish drips wipe up. The bright floor makes small parts easy to find. If you are planning the space, our post on workshop and gym garage ideas is a good place to start, and our list of questions to ask any coating contractor helps you compare quotes.

Kenmore questions

What Kenmore homeowners ask us

Don't see yours? Call 425-226-6085 and an owner will answer it.

How is the cost of a Kenmore garage floor coating figured?+
The cost of a Kenmore garage floor coating is figured from your garage size, slab condition, crack repair, any old coating to remove, stem walls or steps to coat and whether a moisture barrier is needed. A full shop with machines to work around takes more planning. The quote is free, in person and in writing.
Do Kenmore garage slabs hold moisture?+
Some garage slabs in town hold moisture, especially on sloped lots where the garage sits partly below the house. The Kenmore woodshop read 4.1% beside its crack, and nearby slabs have read up to 5.2%. We test in several spots and add a two-layer moisture barrier system when it is needed.
Can you install a floor in Kenmore during fall and winter?+
Yes, we install floors in fall and winter. The woodshop garage on this page was done in October. On install day the crew checks slab moisture and temperature and gives you walk-on and parking times before leaving.
How long does a Penntek floor last?+
A Penntek floor is built as a 30 to 40 year floor, with up to 5x the lifespan of typical epoxy. Typical epoxy often peels or yellows in years 3 to 5. Penntek backs your floor with a limited lifetime warranty.
What is the difference between epoxy and Penntek polyurea?+
The difference between epoxy and Penntek polyurea is how they bond and flex. Epoxy is a rigid film that grips mechanically and can chip, peel and yellow. Penntek's pure polyurea bonds chemically at over 1,300 PSI, stays flexible over cracks and sits under a UV-stable polyaspartic topcoat.
Will a Penntek floor survive my Kenmore woodshop or home gym?+
Yes, a Penntek floor survives a woodshop or home gym. The topcoat resists oil, chemicals and hot tire pickup, and the flexible basecoat handles rolling tool chests, heavy machines and dropped weights. Sawdust and finish drips clean up off the non-porous surface.
What colors hide sawdust and road grit in Kenmore?+
Busy flake blends hide sawdust and road grit well in Kenmore garages, and Tidal Wave and Smoke are reliable choices. Tidal Wave's mix of blue-gray, white and black masks light dust and dark grime alike. Solid colors show everything, so we steer shop owners toward flake.
Do you serve my neighborhood in Kenmore?+
Yes, we serve every neighborhood in Kenmore, including Inglewood, Moorlands, Arrowhead, Uplake, downtown near the river and the homes along Juanita Drive. Our base in Woodinville is a few miles east on SR 522. Call 425-226-6085 to set up a visit.
Will my Kenmore garage really be done in one day?+
Most Kenmore garages are done in one day. The woodshop garage here was, and so were the Bothell and Woodinville floors on this page. If your slab needs a moisture barrier, we tell you at the quote so install day has no surprises.
Can you coat over the old epoxy in my Kenmore garage?+
We check any old epoxy in your Kenmore garage at the free quote. A coating that is already chipping or lifting usually has to be ground off so the new epoxy poly floor bonds to sound concrete, not to a failing film. Read whether Penntek can go over existing epoxy for the full answer.
Who backs the warranty on my floor?+
Penntek backs the warranty on your floor. It is a limited lifetime warranty from the manufacturer, which has dealers in 200+ markets. We record your slab readings on the warranty job card on install day.
Does Cascade Concrete Coatings install epoxy garage floors in Kenmore?+

Yes. We install epoxy poly garage floors across Kenmore using Certified Penntek polyurea instead of epoxy. It looks like a premium flake floor and offers up to 5x the lifespan of typical epoxy. See all our services or book a free in-home quote.

Do you coat patios, walkways and pool decks in Kenmore?+

We do. The same Penntek system that protects garages works on outdoor concrete around Kenmore, with a slip-resistant finish and FadeLock UV stability. See patio and walkway projects.

Do you handle commercial concrete coatings in Kenmore?+

Yes. We coat shops, showrooms, clinics and service bays in and around Kenmore. See our commercial projects.

How do I get a quote for my Kenmore garage floor?+

Call 425-226-6085 or request a free in-home quote. An owner visits, tests your slab and brings color samples. We don't quote over the phone because every slab is different.

Plain talk

Full Disclosure for Kenmore Readers

We wrote this page so people in Kenmore searching for epoxy garage floors and concrete coatings would find us. No secret there. We also wanted it to be useful, so we kept to real readings and real garages from your town and the ones right next to it.

We would like your garage to be our second Kenmore floor on this page. Call 425-226-6085 and we will come test the slab.

Nicole and Sheldon, owners

Let's Get Your Kenmore Shop Floor Sorted

Book a free in-home quote. We will test the slab, check every crack and help you pick a color that suits how you use the space. Call 425-226-6085.

Get my free quote425-226-6085
All 30 cities we serveService area overview →
Ames LakeBellevueBothellCarnationDuvallEdmondsEverettIssaquahKenmoreKentKirklandLake Forest ParkLake StevensLynnwoodMarysvilleMedinaMercer IslandMill CreekMonroeMount VernonMukilteoNewcastleRedmondRentonSammamishSeattleShorelineSnohomishStanwoodWoodinville