Certified Penntek dealer / Woodinville, WAServing Seattle & the EastsideLimited lifetime warranty
Cascade Concrete Coatings
425-226-6085Get a free quote
Redmond Epoxy Poly Coated Garage Floors & Concrete Coatings

Searching Epoxy Floors in Redmond? Start With the Slab.

Remodels, bike rooms, EV bays and one pool deck. Redmond garages work hard, and we coat them with Certified Penntek polyurea after testing the concrete. Most jobs wrap in a single day.

✓Certified Penntek dealer✓Limited lifetime warranty✓Most garages done in one day
Redmond garage floors

Most Redmond homeowners want a garage floor that still looks new in twenty years. Finding one is hard, because a lot of epoxy installers rush the prep and roll on a coating that's built to be redone.

Don't get stuck redoing your floor every few years. We'll test your Redmond slab, prep it right and install a Certified Penntek polyurea floor that bonds with your concrete, so you can stop worrying about the garage and start enjoying it.

The short answer

Cascade Concrete Coatings, a Certified Penntek Dealer, installs epoxy-style garage floor coatings in Redmond with Penntek pure polyurea, a different and longer-lasting material than epoxy. The crew tests moisture and hardness at a free in-home quote, then grinds, repairs and coats most garages in one day. Each floor carries a limited lifetime warranty backed by Penntek. Eight Redmond projects, including a pool deck, are in the portfolio.

Real floors in and around RedmondSee all Redmond projects →
8finished floors in and around Redmond
Up to 5xthe lifespan of typical epoxy
30 to 40year floor, built to bond with your slab
1 dayinstall for a typical garage
What we keep seeing

Your Remodel Looks Done Until You Look Down

Homeowners here renovate a lot, and the garage floor tends to go last. New drywall, fresh paint, cabinets on the wall. Then the slab underneath is still covered in joint compound, primer overspray, paint drips and hairline cracks from years of use.

Two of our 2026 jobs looked exactly like that. One had brand new grey walls over a slab caked in drywall mud, with the water heater closet in the same shape. Another had fresh drywall patches above a floor laced with crazing. The room felt 90% finished and 100% dusty.

Even tidy garages give it away. One local family had white cabinets, a built-in workbench and a pegboard wall, with dark tire lanes running from the door to every parking spot. Bare concrete soaks up whatever rolls in from SR 520 on a wet day.

What we deliver

We'll turn your Redmond garage into a floor you only buy once.

Every Redmond job starts with a moisture and hardness test, then industrial diamond grinding, crack repair with Penntek Mender and a pure polyurea basecoat with a FadeLock UV topcoat. That's how we deliver up to 5x the lifespan of typical epoxy, a 30 to 40 year floor, with a limited lifetime warranty backed by Penntek.

Redmond before and after

Real Redmond floors, before and after.

Drag the handle to compare. Every pair is a real floor our team ground, repaired and coated.

↔BeforeAfter
Certified Penntek vs. typical epoxy or poly

Redmond garage floors fail six ways. We beat all six.

The coating is only half of it. Watch the same slab go through what a Redmond garage puts it through, once with typical epoxy or cheap poly and once the way we install Penntek.

The right system for your concrete

Your slab’s age, composition and moisture all matter. We test it first, then choose the Penntek system that fits, adding a moisture barrier when the readings call for it.

Moisture & hardness tested
Typical epoxy or cheap polySame slab
✕Moisture pushes up from the slab. Blisters and peeling follow.
Certified Penntek by CascadeSame slab
✓Tested first. A moisture barrier goes down when the slab needs one.
Score after round 1Certified Penntek 1, typical epoxy or poly 0
The Penntek advantage

Not all coatings are equal. Watch.

Side-by-side tests on the same slab, in the same conditions. Typical epoxy and cheap poly on one side, certified Penntek on the other.

Stain testOil, brake fluid and road grime wipe right off the non-porous Penntek topcoat, where typical epoxy can absorb stains.
Stretch testPenntek’s flexible basecoat stretches with the concrete. Brittle epoxy cracks and lets go.
Hammer testDropped tools are part of garage life. Typical coatings chip. Penntek resists chips and dents.
Watch the full side-by-side tests →

Settling for a quick epoxy job can leave your Redmond garage peeling by year five.

A floor that fails doesn't just look bad. It means emptying the garage, grinding off the old coating and paying all over again.

✕Peeling where your tires sitSome installers skip diamond grinding, so the coating never truly grips your slab. Hot tires can lift it right off.
✕Yellowing by the garage doorMany epoxies amber in sunlight, so the first few feet of your floor turn a different color than the rest.
✕Cracks showing throughSome crews coat right over cracks. Every bit of slab movement shows up in your floor within a season or two.
✕Moisture blistersPuget Sound slabs hold moisture. Skip the testing and water vapor can push the coating up in bubbles.
✕Paying for it twiceTypical epoxy problems often show in years 3 to 5. Every redo means emptying your Redmond garage and starting over.

We know your garage is more than a place to park. It's part of your home.

For a lot of Redmond families it's the gym, the workshop, the mudroom and the first thing you see when you get home. You've put real money into it. You deserve a floor you never have to think about again, installed by people who treat your home like their own.

Nicole and Sheldon, owners of Cascade Concrete Coatings
The after

Picture pulling into a Redmond garage you're proud of.

Here's what a Certified Penntek floor from our team gives you, long after install day.

✓Clean up in secondsThe non-porous topcoat shrugs off oil, salt and road grime, so a quick wipe keeps your garage looking finished.
✓Color that stays trueFadeLock UV stability keeps the floor by the open door matching the back wall, year after year.
✓A floor that moves with your slabThe flexible basecoat handles Northwest temperature swings and settling, so your Redmond floor doesn't crack with the concrete.
✓Your garage back in a dayA typical garage is finished in one day. Before we leave, the crew gives you clear walk-on and parking times.
✓Coverage that outlasts any one shopYour limited lifetime warranty is backed by Penntek, the manufacturer, so it isn’t tied to one small company.
✓A garage that adds to your homeA finished, showroom-clean floor makes a strong first impression for guests, and for buyers when it’s time to sell.
Performance at every layer

Typical epoxy is one coat. Ours is a system.

Every certified Penntek floor is built in four layers, each doing its own job. Watch it go down layer by layer, then tap a layer to see what it does for your floor.

01020304

When moisture readings call for it, we add a two-layer moisture barrier system before the basecoat.

Material matters

Why Your Next Floor Shouldn't Be Plain Epoxy

You probably found us by searching for an epoxy garage floor. Most people do. The flake-and-gloss look you have in mind is exactly what we install. The chemistry under it is what's different.

Epoxy sets into a hard, brittle layer with a mechanical grip. Slabs on the Eastside see wet winters, the odd hard freeze and warm summers. Concrete moves through all of that. Brittle coatings crack, then hot tires pull them up in the parking lanes. Sun through a south-facing door turns them amber.

Certified Penntek polyurea is a proprietary pure polyurea blend at over 99% solids. It makes a 1,300+ PSI chemical bond with ground concrete and flexes with the slab instead of fighting it. The polyaspartic topcoat is non-porous, so oil, road salt and brake dust wipe off. FadeLock™ UV stability passed a 16-hour QUV test, which is why a pool deck in full summer sun is a fair test of it.

So when someone asks for epoxy poly garage floors, this is what they end up with. See the difference with your own eyes on the Penntek vs epoxy demo.

01 / 04Proprietary pure polyureaThe basecoat is Penntek's own pure polyurea blend, over 99% solids. It flexes as your slab moves through Redmond's wet winters and warm summers, so it doesn't crack and lift like rigid epoxy.
02 / 04Prep by certified installersPenntek trains and certifies the people who touch your floor. They run industrial diamond grinders, fix cracks with Penntek Mender and add a two-layer moisture barrier system when the meter says so.
03 / 04Backed by the manufacturerA limited lifetime warranty backed by Penntek covers every floor we install. Penntek is in 200+ markets, so the company behind your warranty is not a one-truck operation.
04 / 04A better product overallBuilt for 30 to 40 years and up to 5x the lifespan of typical epoxy. It's the longest-lifespan concrete coating with the lowest lifetime cost of ownership.
Watch the side-by-side tests →How the Penntek warranty works →
Not your typical epoxy crew

Professionally trained installers

Anyone can buy a kit and call themselves a garage floor company. Penntek doesn't sell to just anyone. Our team was vetted, trained hands-on through Penntek Academy and is backed by Penntek's full-time technical support team from prep to finish. That's the Penntek Standard, on every floor we install.

Certified Penntek Dealer

What "Certified Penntek Dealer" actually means

  1. 01Vetted before trainingPenntek reviews every company first. Many never make it to training.
  2. 02Hands-on training at PenntekChemistry, slab analysis, prep, application and troubleshooting, taught by Penntek’s technical team.
  3. 03Exclusive formulasPenntek’s proprietary polyurea is sold only to certified dealers. You can’t buy it at a store.
  4. 04Backed on every jobPenntek’s technical support team backs our crew from prep to finish, and Penntek backs your floor’s limited lifetime warranty.
What we coat in Redmond

Any concrete, inside or out.

Garages are most of what we do in Redmond, but the same Penntek system protects patios, pool decks, basements and commercial floors.

Garage floorsEpoxy poly garage floors for Redmond homes, from one-car to four-car.Patios & walkwaysWeather-ready, slip-resistant coatings for outdoor concrete.Pool decksA good-looking, durable finish around the water.BasementsMoisture-tested coatings for finished and unfinished basements.Commercial floorsShops, showrooms and clinics in and around Redmond.
How it works

Your Path to a Finished Garage Floor

The steps are simple. The details, from grinding to topcoat, are laid out on our how we install page.

  1. 01Free quote, meter in handWe come out, measure, meter moisture, scratch test the surface and note every crack, step and stem wall. You get a written quote with no pressure attached.
  2. 02Install day, start to finishClear the space. The crew grinds, repairs, coats and cleans up, usually in one day. Before leaving they check the slab and tell you when to walk on it and park.
  3. 03Back to bikes, cars and projectsRoll everything back in. Your new floor shrugs off mud, oil and hot tires, and it carries a limited lifetime warranty backed by Penntek.
Who's doing the work

We Show Up After the Other Trades and Finish the Room

Cascade Concrete Coatings is a Certified Penntek Dealer based in Woodinville, just north up the Sammamish River valley. We are the crew you call once the framers, electricians and painters pack up.

We plan around your remodel. On one job we did the consultation in July while the walls were still open studs, then came back in October once paint was dry. The slab was ground clean and coated in Domino flake in a single day.

Every quote starts with a meter and a scratch test. Readings in town have run from 3.4% to 5.4%, and a sound slab with crazing gets treated differently from a slick new pour. We tell you what we found and why the plan looks the way it does.

See the full install process →
Is it right for you?

Is a Penntek floor right for your Redmond home?

You're probably a great fit if any of these sound familiar.

Choosing a blend

Find Your Flake for a Garage That Works Hard

Local picks for concrete coatings lean a little bolder than most. Domino, a high-contrast black, white and grey, finished off a full remodel. Slate Stone has been chosen twice. Ash went into a garage that needed to stop showing oil stains.

Think about what lives in your garage. Bikes with muddy tires, a workbench throwing sawdust, two cars dripping rain. Busy multi-tone flake hides it all. Lighter blends make a deep tandem bay feel open. Browse every Penntek style and color before we bring samples over.

Slate StoneEvolution FlakeChosen for two garages in town, including a 5.4% tandem bay. Grey, tan and black flake gives a natural stone look that hides bike-tire mud and sawdust between sweeps.DominoEvolution FlakeFor the homeowner who wants the floor to make a statement. Domino is high-contrast black, white and grey, and it capped a full Redmond garage remodel with crisp white walls.AshEnviroflakeA light, clean Enviroflake in soft grey and white. It brightened an oil-stained garage on our list and suits smaller townhome garages where daylight is limited.Pebble BeachEvolution FlakeSoft grey and tan that works in garages, patios and walkways. Pebble Beach is a good pick if you want the garage and a back patio to match.
See every color and system →
Redmond floors, real readings

Take a Look at What Your Neighbors Chose

Every concrete coating project here started with numbers. Square footage, moisture readings, cracks and the stuff that couldn't move, like cabinets on legs or a water heater on a stand.

Two more from 2026 are worth opening. A 389.5 square foot garage with a raised landing and two stairs was coated in Silver Creek with a slab temperature of 67°F on install day. And a newly drywalled garage got crack repair and Slate Stone flake, water heater closet included. See all of them on the portfolio page.

More floors in and around Redmond

See all Redmond projects →
Silver Creek Evolution garage floor coating in Redmond, WA by Cascade Concrete CoatingsRedmondSilver Creek Flake Garage and Landing in RedmondSlate Stone Evolution garage floor coating in Redmond, WA by Cascade Concrete CoatingsRedmondSlate Stone Flake Garage Floor Remodel in Redmond
Reviews

Hear it from your neighbors.

All reviews →
Loading Google reviews…
Free in-home quote in Redmond

Get the Redmond garage floor everyone wishes they had.

An owner comes out, tests your slab, brings real color samples and writes a clear quote. No pressure, just a plan for a floor you'll only buy once.

Book my free quote425-226-6085
Neighborhoods we cover

From Education Hill to Redmond Ridge, We Know Your Garage

Redmond has more kinds of garages than most people realize. Education Hill and Grass Lawn have plenty of 1970s and 1980s homes with two-car garages, older slabs and that fine surface crazing you see on aging concrete. Out on Redmond Ridge and in the newer Bear Creek subdivisions, garages are newer, often deep tandem bays, and the concrete is still clean enough to protect before it stains.

Overlake and the neighborhoods around the Microsoft campus have a lot of townhomes and newer builds with compact garages that double as EV charging spots. Downtown, near Redmond Town Center and the Sammamish River Trail, garages are often bike rooms first. This is the Bicycle Capital of the Northwest, after all. Toward Marymoor Park and the north end of Lake Sammamish you'll find bigger lots, pool decks and patios we can coat too.

We also coat floors in Kirkland, just over the hill, Sammamish on the plateau, Bellevue to the south and Woodinville, our home base. The Redmond page on Wikipedia has the city's backstory, and the City of Redmond is the place to check if your garage is part of a permitted remodel.

Nearby we also serve
KirklandSammamishBellevueWoodinvilleBothell
What's at stake

One Weekend Kit or a Floor You Never Redo

A big box epoxy kit feels like a smart shortcut. You spend a weekend moving everything out, rolling it on and waiting. By year three you might see peeling where you park, a yellow cast near the door and small bubbles where moisture pushed up. Then you move everything out a second time and pay someone to grind it off.

Or you spend one day with a crew that preps it right. You come home to a garage that finally looks as good as the rest of the remodel. Mud from the Sammamish River Trail rinses off. Drips bead up. The floor is built for 30 to 40 years, up to 5x the lifespan of typical epoxy.

Planning a gym or workshop out there? Our guide to workshop, gym and hobby garage ideas is a good next read, and so is how a slab gets prepped for coating.

Redmond questions

What Redmond homeowners ask us

Don't see yours? Call 425-226-6085 and an owner will answer it.

How is the price set for a Redmond garage floor coating?+
The price of a Redmond garage floor coating comes down to square footage, surface condition, crack repair, any old coating to remove and whether a moisture barrier is needed. Stairs, landings and stem walls add a bit. We measure and test at a free in-home quote and give you a written number.
Should I coat my Redmond garage before or after a remodel?+
Coat your Redmond garage floor after the remodel, once drywall, paint and cabinets are done. Saws, ladders and mud buckets will scratch a fresh floor. We can do the consult early to plan, like the Domino job we tested in July and coated in October.
Is moisture an issue in Redmond garage slabs?+
Moisture can be an issue in Redmond garage slabs, so we test every one. Our local readings have ranged from 3.4% to 5.4%. Higher numbers get the two-layer moisture barrier system under the basecoat. Our article on whether moisture will ruin a coating explains the thinking.
What time of year is good for a coating in Redmond?+
Any time of year works for a coating in Redmond. We have installed here in July, September, October and November. On install day the crew checks slab moisture and temperature, then gives you walk-on and parking times before they leave.
How long does a Penntek floor last compared to epoxy?+
A Penntek floor is built to last 30 to 40 years, up to 5x the lifespan of typical epoxy. Epoxy floors often peel, yellow or soften under hot tires much sooner. Every Penntek floor we install also comes with a limited lifetime warranty backed by Penntek.
What's the difference between epoxy and polyurea?+
The difference between epoxy and polyurea is flexibility and bond. Epoxy is rigid and grips the surface. Penntek polyurea is a pure blend over 99% solids that chemically bonds at 1,300+ PSI and flexes with concrete. The look is similar, which is why people call it an epoxy polyurea floor.
Can my Redmond garage handle an EV, bikes and a workbench?+
Yes, a Penntek garage floor handles EVs, bikes and a workbench easily. The polyaspartic topcoat resists hot tire pickup, oil, salt and chemicals. Heavy cars, kickstands and rolling tool carts are everyday use. Spills and sawdust sweep or wipe right up.
Which Redmond colors hide mud and trail grit?+
Multi-tone flakes like Slate Stone, Smoke and Silver Creek hide mud and trail grit in local garages. They break up dirt from bike tires and wet cars between cleanings. Bold Domino hides well too. Light solids look sharp but show more.
Do you cover Redmond Ridge, Overlake and Education Hill?+
Yes, we cover Redmond Ridge, Overlake, Education Hill, Grass Lawn, Bear Creek, downtown Redmond and the neighborhoods toward Marymoor Park and Lake Sammamish. We're based in Woodinville, close enough that quotes and install days are easy to schedule.
Can you coat pool decks and patios in Redmond too?+
Yes, we coat pool decks and patios in Redmond, not just garages. One local pool deck had a failing coating stripped off and got Quartzite flake in April 2026. Read more about coating patios, basements and driveways.
What warranty comes with the floor?+
Your floor comes with a limited lifetime warranty backed by Penntek, the manufacturer. That backing matters because the coverage doesn't depend on a single installer alone. We go over the terms at your free in-home quote so you know exactly what's included.
Does Cascade Concrete Coatings install epoxy garage floors in Redmond?+

Yes. We install epoxy poly garage floors across Redmond using Certified Penntek polyurea instead of epoxy. It looks like a premium flake floor and offers up to 5x the lifespan of typical epoxy. See all our services or book a free in-home quote.

Do you coat patios, walkways and pool decks in Redmond?+

We do. The same Penntek system that protects garages works on outdoor concrete around Redmond, with a slip-resistant finish and FadeLock UV stability. See patio and walkway projects.

Do you handle commercial concrete coatings in Redmond?+

Yes. We coat shops, showrooms, clinics and service bays in and around Redmond. See our commercial projects.

How do I get a quote for my Redmond garage floor?+

Call 425-226-6085 or request a free in-home quote. An owner visits, tests your slab and brings color samples. We don't quote over the phone because every slab is different.

Straight talk

We'll Be Honest About This Page

We put this page together so Redmond homeowners searching for epoxy garage floors and concrete coatings would land on a company that has actually worked here. Instead of fluff, we filled it with real projects, real readings and plain answers.

Thanks for reading this far. Call us at 425-226-6085 or set up your free in-home quote, and we'll bring the moisture meter.

Nicole and Sheldon, owners

Let's Finish Your Redmond Garage the Right Way

Call 425-226-6085 or request a free in-home quote. We'll test the slab and bring real flake samples to your garage.

Get my free quote425-226-6085
All 30 cities we serveService area overview →
Ames LakeBellevueBothellCarnationDuvallEdmondsEverettIssaquahKenmoreKentKirklandLake Forest ParkLake StevensLynnwoodMarysvilleMedinaMercer IslandMill CreekMonroeMount VernonMukilteoNewcastleRedmondRentonSammamishSeattleShorelineSnohomishStanwoodWoodinville